Kelvinator JS4BD030KB Guía de instalación Pagina 18
- Pagina / 20
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
18
COMFORT ALERT TROUBLESHOOTING - CONTINUED
Table 10. LED Diagnostics - Continued
Status LED Status LED Description Status LED Troubleshooting Information
ALERT
Flash Code 6
(Yellow LED)
Open Start Circuit
Current only in run circuit
• Runcapacitorhasfailed
• Opencircuitincompressorstartwiringorconnections
— Check wiring and connectors between supply and the compressor S terminal
• Compressorstartwindingisdamaged
— Check compressor motor winding resistance
ALERT
Flash Code 7
(Yellow LED)
Open run circuit
Current only in start circuit
• Opencircuitincompressorrunwiringorconnections
— Check wiring and connectors between supply and the compressor R terminal
• Compressorrunwindingisdamaged
— Check compressor motor winding resistance
ALERT
Flash Code 8
(Yellow LED)
Welded Contactor
Compressor always runs
• Compressorcontactorhasfailedclosed
• Thermostatdemandsignalnotconnectedtomodule
ALERT
Flash Code 9
(Yellow LED)
Low Voltage
Control circuit < 17VAC
• Controlcircuittransformerisoverloaded
• Lowlinevoltage(contactutilityifvoltageatdisconnectislow)
• Checkwiringconnections
* Flash code number corresponds to a number of LED flashes, followed by a pause and then repeated. Trip and alert LED’s
flashing at same time means control circuit voltage is too low for operation.
Table 11. Module Wiring Troubleshooting
Miswired Module Indication Recommended Troubleshooting Action
Green LED is not on, module does not power up
• DetermineifbothR & C module terminals are connected.
• Verifyvoltageispresentatmodule’sR & C terminals.
Green LED intermittent, module powers up only when compressor
runs
• DetermineifR & Y terminals are wired in reverse.
• VerifymodulesR&Cterminalshaveaconstantsource.
Trip LED is on, but system and compressor check OK
• VerifyY terminal is connected to 24VAC at contactor coil.
• Verifyvoltageatcontactorcoilfallsbelow0.5VACwhenoff.
• Verify24VACispresentacrossY & C when thermostat demand signal is preset. If not,
R & C are reversed wired.
TRIP LED & ALERT LED flashing together • VerifyR & C terminals are supplied with 19 - 28VAC.
ALERT Flash CODE 3 displayed incorrectly
(Compressor short cycling)
• VerifyY terminal is connected to 24VAC at contactor coil.
• Verifyvoltageatcontactorcoilfallsbelow0.5VACwhenoff.
ALERT Flash Code 5, 6, or 7 displayed incorrectly
(Open Circuit, Open Start Circuit or Open Run Circuit)
• Verify the compressorrun andstartwires are routedthrough the module’scurrent
sensing holes.
• VerifytheY terminal is connected to 24VAC at contactor coil.
• Verifyvoltageatcontactorcoilfallsbelow0.5VACwhenoff.
ALERT Flash Code 6 (Open Start Circuit) displayed for Code 7
(Open Run Circuit) or vice-versa
• Verifythecompressorrunandstartwiresareroutedthroughthecorrectmodulesensing
holes.
ALERT Flash Code 8 displayed incorrectly (Welded Contactor)
• Determineifmodule’sY terminal is connected.
• VerifyY terminal is connected to 24VAC at contactor coil.
• Verify24VACispresentacrossY & C when thermostat demand signal is present. If
not, R & C are reversed wired.
• Verifyvoltageatcontactorcoilfallsbelow0.5VACwhenoff.
• ReviewThermostatDemandWiring(page10)forY & C wiring.
Relacionado con productos y manuales para Acondicionadores de aire del sistema de división Kelvinator JS4BD030KB
(16 paginas)Rexel 2101982 Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Zubehör für Papierschneider Rexel 2101982.
Wir stellen 1 PDF-Handbücher Rexel 2101982 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Datenblatt
Comentarios a estos manuales